Home | Map | Projects | Construction | Soldering | Study | Components | 555 | Symbols | FAQ | Links
Electronics Club

Tools required for electronics

Also see: Starter kit | Workbench | Soldering guide



Rapid Electronics stock a wide range of tools and they have kindly allowed me to use their photographs on this page.
Soldering iron, photograph © Rapid Electronics

Soldering iron

For electronics work the best type is one powered by mains electricity (230V in the UK), it should have a heatproof cable for safety. The iron's power rating should be 15 to 25W and it should be fitted with a small bit of 2 to 3mm diameter.

Photograph © Rapid Electronics
Other types of soldering iron
Low voltage soldering irons are available, but their extra safety is undermined if you have a mains lead to their power supply! Temperature controlled irons are excellent for frequent use, but not worth the extra expense if you are a beginner. Gas-powered irons are designed for use where no mains supply is available and are not suitable for everyday use. Pistol shaped solder guns are far too powerful and cumbersome for normal electronics use.


Soldering iron stand, photograph © Rapid Electronics

Soldering iron stand

You must have a safe place to put the iron when you are not holding it. The stand should include a sponge which can be dampened for cleaning the tip of the iron.

Photograph © Rapid Electronics


Solder sucker, photograph © Rapid Electronics

Desoldering pump (solder sucker)

A tool for removing solder when desoldering a joint to correct a mistake or replace a component.

Photograph © Rapid Electronics


Solder remover wick (copper braid)

This is an alternative to the desoldering pump shown above.

Photograph © Rapid Electronics


Solder reels, photograph © Rapid Electronics

Reel of solder

The best size for electronics is 22swg (swg = standard wire gauge).

Photograph © Rapid Electronics


Side cutters, photograph © Rapid Electronics

Side cutters

For trimming component leads close to the circuit board.

Photograph © Rapid Electronics


Wire strippers (automatic), photograph © Rapid Electronics

Wire strippers

Most designs include a cutter as well, but they are not suitable for trimming component leads.

Photograph © Rapid Electronics


Snipe nose pliers, photograph © Rapid Electronics

Small pliers

Usually called 'snipe nose' pliers, these are for bending component leads etc. If you put a strong rubber band across the handles the pliers make a convenient holder for parts such as switches while you solder the contacts.

Photograph © Rapid Electronics


Screwdriver, photograph © Rapid Electronics

Small flat-blade screwdriver

For scraping away excess flux and dirt between tracks, as well as driving screws!

Photograph © Rapid Electronics


Crocodile clip, photograph © Rapid Electronics

Heat sink

You can buy a special tool, but a standard crocodile clip works just as well and is cheaper.

Photograph © Rapid Electronics


Track cutter, photograph © Rapid Electronics The following tool is only required if you are using stripboard:

Track cutter

A 3mm drill bit can be used instead, in fact the tool is usually just a 3mm drill bit with a proper handle fitted.

Photograph © Rapid Electronics


PCB rubber, photograph © Rapid Electronics The following tools are only required if you make your own PCBs:

PCB rubber

This is an abrasive rubber for cleaning PCBs. It can also be used to clean stripboard where the copper tracks have become dull and tarnished.

Photograph © Rapid Electronics

PCB drill in stand, photograph © Rapid Electronics

Small electric drill

Ideally this should be mounted in a drill stand. You will need a range of small drill bits, but for most holes a 1mm bit is suitable. Larger holes can be drilled with a hand drill but 1mm bits are too fragile to use reliably in a hand drill.

Photograph © Rapid Electronics


Click here for Rapid Electronics Rapid Electronics stock a wide range of tools and they have kindly allowed me to use their photographs on this page. We buy most of our tools and components for the Electronics Club from Rapid Electronics. The photographs are from their Image Gallery CD-ROM.


© John Hewes 2007, The Electronics Club, www.kpsec.freeuk.com
This site was whacked using the TRIAL version of WebWhacker. This message does not appear on a licensed copy of WebWhacker.